77.150.30 (Copper products) 标准查询与下载

ASTM B422/B422M-15 铜铝硅钴合金, 铜镍硅镁合金, 铜镍硅合金, 铜镍铝镁合金和铜镍锡合金薄板和带材的标准规格

1.1 This specification establishes the requirements for2 Copper Alloy UNS Nos. C19002, C19010, C19015, C19020, C19025, C63800, C64725, C70250, C70260, C70265, and C70310 sheet and strip. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 The following safety hazard caveat pertains only to the test method(s) described in this specification. 1.3.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Copper-Aluminum-Silicon-Cobalt Alloy, Copper-Nickel-Silicon-Magnesium Alloy, Copper-Nickel-Silicon Alloy, Copper-Nickel-Aluminum-Magnesium Alloy, and Copper-Nickel-Tin Alloy Sheet and Strip

ASTM B61-15 焊接镍和镍钴合金管的标准规范

1.1 This specification2 establishes requirements for a high-grade steam-metal or valve-bronze alloy (Copper Alloy UNS No. C922003) used for component castings of valves, flanges, and fittings. 1.2 The castings covered are used in products that may be manufactured in advance and supplied from stock by the manufacturer or other dealer. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Steam or Valve Bronze Castings

ASTM B22/B22M-15 桥梁和转盘青铜铸件标准规范

1.1 This specification establishes requirements for bronze castings for turntables, movable bridges and bridge parts, and bronze castings suitable for use in bridges and other structures for fixed and expansion bearings in which motion is slow and intermittent. The following Copper Alloys are specified: UNS No. C86300, C90500, C91100, C91300, and C93700. Note 1: Historically, the alloys in this specification have been used in the applications listed in Appendix X1. Actual practice may vary.2 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 The following safety hazard caveat pertains only to the test method(s) described in this specification: 1.3.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Bronze Castings for Bridges and Turntables

ASTM B103/B103M-15 磷青铜板、薄板、带材和轧制棒材的标准规范

1.1 This specification establishes the requirements for copper-tin alloy (phosphor bronze), copper-tin-lead alloy (leaded phosphor bronze), and copper-tin-lead-zinc alloy (bearing bronze), plate, sheet, strip, and rolled bar. The phosphor bronzes commonly are used for deep drawing into bellows and stamping and forming into spring devices and into terminals and connectors for electrical apparatus because they combine high strength with high elongation. The leaded phosphor bronzes are used where strength, corrosion resistance, and machinability are required. The bearing bronze is used in bushings, bearings, and load-bearing thrust washers. The following alloys are covered: Copper Alloy UNS No.2 Nominal Composition, % Previously Used Designation Copper Tin Zinc Lead             C51000 95 5 . . . . . . A1 C51100 96 4 . . . . . .

Standard Specification for Phosphor Bronze Plate, Sheet, Strip, and Rolled Bar

ASTM B763/B763M-15 阀门用铜合金砂型铸件标准规范

1.1 This specification establishes requirements for copper alloy sand castings for valve applications. Nominal compositions of the alloys defined by this specification are shown in Table 1.2 (A) Phosphorus 0.13(B) Phosphorus 0.1(C) Antimony 0.07, Boron 0.001. Note 1: This specification does not cover Copper Alloy UNS Nos. C83600, C92200, C96200, and C96400. These alloys are also used in valve applications. They are covered by the following specifications: C83600: B62 C92200: B61 C96200: B369 C96400: B369 1.2 The castings produced under this specification are used in products which may be manufactured in advance and supplied for sale from stock by the manufacturer. 1.3 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Copper Alloy Sand Castings for Valve Applications

ASTM B62-15 电镀用钼和钼合金的制备

1.1 This specification2 establishes requirements for an alloy having a composition of copper, tin, lead, and zinc, used for component castings of valves, flanges, and fittings. The common trade name of this alloy is 85-5-5-5; the correct identification is Copper Alloy UNS No. C83600.3 1.2 The castings covered are used in products that may be manufactured in advance and supplied from stock from the manufacturer or other dealer. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Standard Specification for Composition Bronze or Ounce Metal Castings

ASTM B770-15 通用铜铍合金砂型铸件标准规范

1.1 This specification establishes requirements for copper-beryllium alloy sand castings for general applications and nominal compositions alloys defined by this specification are shown in Table 1.2 (A) When fine-grained castings are specified, 0.02 to 0.12 titanium is added for grain refinement, usually in the remelt ingot. See Specification B30. 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following safety hazard caveat pertains only to the test methods described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Specification for Copper-Beryllium Alloy Sand Castings for General Applications

ASTM B249/B249M-15 锻铜和铜合金棒、棒材、型材和锻件的一般要求

12.1 For the purpose of determining compliance with the specified limits for requirements of the properties listed in the following table and for dimensional tolerances, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29. Property 8199;8199;8199;Rounded Unit for Observed or 8199;8199;8199; 8199;8199;8199;Calculated Value     Chemical composition nearest unit in the last right-hand significant8199;digit used in expressing the limiting value Hardness Electrical resistivity Electrical conductivity     Tensile strength nearest ksi [5 MPa] Yield strength     Elongation: nearest 18201;% 8199;   Grain size:   8199;Under 0.060 mm nearest mult......

Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings

ASTM B134/B134M-15 黄铜线标准规范

1.1 This specification establishes requirements for round, hexagonal, octagonal, rectangular and square brass wire of UNS Alloy Nos. C21000, C22000, C22600, C23000, C23400, C24000, C26000, C27000, and C27400. 1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Brass Wire

ASTM B188-15 无缝铜母线管的标准规格

18.1 For purposes of determining compliance with the specified limits for requirements of the properties listed in the following table, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29. Property Rounded Unit for Calculated or Observed Value   8199;Chemical composition nearest unit in the last right-hand place of figures 8199;8199;of the specified limit 8199;Hardness   8199;Electrical resistivity nearest unit in the last right-hand place of figures 8199;Electrical conductivity 8199;Tensile strength nearest ksi (5 MPa) 8199;Elongation: below 58201;% nearest multiple of 0.58201;% 8199;58201;% and over nearest 18201;% 1.1 This specification establishes the requirements for seamless copper bus pipe and tube intended for use as electrical conductors. 1.1.1 The product shall be made from one of the following coppers, as denoted in the ordering information:2 Copper UNS No.2

Standard Specification for Seamless Copper Bus Pipe and Tube

ASTM B19-15 镁合金永久模具铸件标准规范

1.1 This specification establishes the requirements for sheet, strip, plate, bar, and disks for the manufacture of ammunition component parts thereof from alloy UNS C26000. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard. 1.2.1 Exception—Values given in inch-pound units are the standard except for grain size which is stated in metric units. 1.3 The following safety caveat pertains only to the test method described in Section 10 of this specification. (Warning—Mercury has been designated by many regulatory agencies as a hazardous material that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Safety Data Sheet (SDS) for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law.) 1.4  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Cartridge Brass Sheet, Strip, Plate, Bar, and Disks

ASTM B763/B763M-14 阀门应用铜合金砂铸件标准规格

1.1 This specification establishes requirements for copper alloy sand castings for valve applications. Nominal compositions of the alloys defined by this specification are shown in Table 1.2 TABLE 1 Nominal Compositions Classification Copper Alloy UNS No. Commercial Designation Copper Tin Lead Zinc Nickel Iron Alumi- num Man- ganese Sili- con Bismuth Sele- nium Leaded red brass C83450  ......

Standard Specification for Copper Alloy Sand Castings for Valve Applications

ASTM B467-14 焊接铜镍管的标准规格

18.1 For purposes of determining compliance with the specified limits for requirements of the properties listed in the following table, and observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29. Property Rounded Unit for Observed or Calculated Value   Chemical composition nearest unit in the last right-hand place of figures of the specified limit Tensile strength Yield strength nearest ksi (nearest MPa up to 10 ksi, incl, nearest 5 MPa over 10 ksi) Elongation nearest 18201;% 1.1 This specification establishes the requirements for welded copper-nickel alloy pipe for general engineering purposes. The following alloys are covered:2 Copper Alloy UNS No.2 Type of Metal     C70600 90-10 copper-nickel C70620 90-10 copper-nickel   (Modified for Welding) C71500 70-30 copper-nickel C71520 70-30 copper-nickel   (Modified for Welding) 1.2 Units—The values sta......

Standard Specification for Welded Copper-Nickel Pipe

ASTM B806-14 通用铜合金永久铸模铸件的标准规格

1.1 This specification establishes requirements for copper alloy2 permanent mold castings for general applications. Nominal compositions of the alloys under this specification are shown in Table 1.TABLE 1 Nominal Composition Classification Copper Alloy UNS No. Nominal Composition Copper Aluminum Iron Manganese Nickel (incl Cobalt) Silicon Lead Zinc Tin Yellow brass C85470A 62.5

Standard Specification for Copper Alloy Permanent Mold Castings for General Applications

ASTM B22/B22M-14 桥板和转盘用青铜铸件标准规格

1.1 This specification establishes requirements for bronze castings for turntables, movable bridges and bridge parts, and bronze castings suitable for use in bridges and other structures for fixed and expansion bearings in which motion is slow and intermittent. The following Copper Alloys are specified: UNS No. C86300, C90500, C91100, C91300, and C93700.Note 1—Historically, the alloys in this specification have been used in the applications listed in Appendix X1. Actual practice may vary.2 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Bronze Castings for Bridges and Turntables

ASTM B411/B411M-14 铜镍硅合金杆材和棒材的标准规格

1.1 This specification establishes the requirements for copper-nickel-silicon alloy rod and bar produced from Copper Alloy UNS No. C64700 in straight lengths. 1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Copper-Nickel-Silicon Alloy Rod and Bar

ASTM B271/B271M-14 铜基合金离心铸件标准规格

1.1 This specification establishes requirements for centrifugal castings of copper-base alloys having the nominal compositions shown in Table 1.TABLE 1 Nominal Compositions Classification Copper Alloy UNS No. Commercial Designation Copper Tin Lead Zinc Nickel Iron Alum- inum Mang- anese Silicon Leaded red brass C83600 85-5-5-5 85 5  5  5

Standard Specification for Copper-Base Alloy Centrifugal Castings

ASTM B820-14 铜和铜合金带材可成形性测定用弯曲试验的标准试验方法

5.1 This bend test provides information as to the formability or the ability of copper and copper alloy strip to resist cracking when being formed. 5.2 This test method can be used as a quality control tool to determine if material will form to a given radius. 5.3 This test method is also useful in research and development to provide data for use in selecting a spring material that will safely form to the geometry of a given part. 5.4 The results are suitable for direct application in design and manufacturing, only when all factors such as the geometry of the part, punch and die design, lubrication, stamping speed, and other material properties are known. 1.1 This test method describes the technique of bend testing copper and copper alloy strip samples to determine product formability or the ability to resist cracking when forming a bend around a specific radius. The criterion for failure is the occurrence of cracks on the outer radius of curvature (convex). 1.2 This bend test is limited to strip from 0.003 to and including 0.031 in. thick. (0.076 to and including 0.79 mm). 1.3 The size of the forming radii used in this test shall be 0.005 to and including 0.250 in. (0.127 to and including 6.35 mm). 1.4 Units—Values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units which are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Bend Test for Determining the Formability of Copper and Copper Alloy Strip

ASTM B820-14a 铜和铜合金带材可成型性测定用弯曲试验的标准试验方法

5.1 This bend test provides information as to the formability or the ability of copper and copper alloy strip to resist cracking when being formed. 5.2 This test method can be used as a quality control tool to determine if material will form to a given radius. 5.3 This test method is also useful in research and development to provide data for use in selecting a spring material that will safely form to the geometry of a given part. 5.4 The results are suitable for direct application in design and manufacturing, only when all factors such as the geometry of the part, punch and die design, lubrication, stamping speed, and other material properties are known. 1.1 This test method describes the technique of bend testing copper and copper alloy strip samples to determine product formability or the ability to resist cracking when forming a bend around a specific radius. The criterion for failure is the occurrence of cracks on the outer radius of curvature (convex). 1.2 This bend test is limited to strip from 0.003 to and including 0.031 in. thick (0.076 to and including 0.79 mm). 1.3 The size of the forming radii used in this test shall be 0.005 to and including 0.250 in. (0.127 to and including 6.35 mm). 1.4 Units—Values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units which are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Bend Test for Determining the Formability of Copper and Copper Alloy Strip

ASTM B271/B271M-14a 铜基合金离心铸件的标准规格

1.1 This specification establishes requirements for centrifugal castings of copper-base alloys having the nominal compositions shown in Table 1. (A) Phosphorus 0.13 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

Standard Specification for Copper-Base Alloy Centrifugal Castings